|
Post by gurra11 on Jun 5, 2011 0:21:25 GMT 1
Jag sitter och kollar på virke till bracing. Eller finns det ett svenskt ord? Iallafall så finns det sågat bracing virke men även något som är hand split. Hand split verkar kosta dubbelt så mycket. Är det någon skillnad/fördel med något av det? www.alaskawoods.com/products.php?catid=3&category=Bracewood
|
|
|
Post by snapcase on Jun 5, 2011 7:11:43 GMT 1
As you can see in that site, most spruce cuts are sawn. Machine sawn in fact without much concern. Splitting spruce with a wedge and a hammer is the traditional and best way to do it to avoid runout. Braces or top plates without runout are always better and more consistent for guitar building. The reason why is not so common amongst wood seller is that it wastes a lot of "useable" wood. This why is more expensive. Almost every good luthier splits his spruce billets on his own and never buy pre cur tops or bracewood. Of course factories are different. Don't expect to find split spruce cuts in any factory guitar. You an check about runout here.==== Som ni kan se på detta ställe, de flesta gran nedskärningar sågas. Maskinen sågade i själva verket utan större bekymmer. Uppdelning gran med en kil och en hammare är det traditionella och bästa sättet att göra det för att undvika runout. Hängslen eller takplåtar utan runout är alltid bättre och mer konsekvent för gitarr byggnad. Anledningen är inte så vanligt bland ved säljare är att det är slöseri med en hel del "användbar" trä. Detta varför är dyrare. Nästan varje god instrumentmakare delar upp sin gran tackor på sin egen och aldrig köper färdiga klippa toppar eller bracewood. Naturligtvis fabriker är olika. Räkna inte med att hitta dela gran nedskärningar i någon fabrik gitarr. Dig en check om runout här.
|
|
|
Post by snapcase on Jun 5, 2011 7:47:09 GMT 1
I will post only in English for tech chat. Sorry. Understanding runout can be tricky but it's easy. Literally it means runing out... out of where? It's when the wooden fibers are running or oriented not parallel to the board or braces outer surfaces. Let's consider the three axis over a piece of spruce. Check the image below If we look from the Y axis we can have a perfectly aligned and regular grain. Watching from the X axis the grain also is uniform, vertically aligned and looking good. But what if we look at the board or a brace from the Z axis? Ideally, wooden fibers should run parallel to the board outer surfaces, but we cannot see it with bare eyes. If we split a piece of wood we can have the following situations: 1- the wood splits parallel to the outer surfaces. That means no runout. This is an optimum wood cut for guitar building. 2- The wood splits at an angle. In this particular case (see the picture below) the fibers are not oriented running all along the board or a brace, they run slanted or at an angle. As you can see in the picture the fibers run upwards. In a long wooden piece like a top plate or a brace the fibers might be running only in a part of the piece and not along the entire piece from end to end. Since the wooden fibers are not continuous from end to end of the board, this wooden piece will be weaker and structurally less reliable. This is important. Braces made like this (sawn) have a higher tendency to break and split because the fibers are not continuous. Spruce without runout is always stronger, stiffer and structurally more uniform for the same size and weight. Using braces with runout may force builders to use bigger, thicker and more weighty braces to get the same stiffness target which is usually a drawback to make a powerful guitar top, and in other hand, yields more prone to fail tops and braces.
|
|
Tyko
Allvetande
www.runessonguitars.com
Posts: 6,085
|
Post by Tyko on Jun 5, 2011 22:17:24 GMT 1
Självklart finns det svenska ord för alla gitarrbyggartermer! Att använda engelska ord låter i mina öron ofta mycket konstigt och speciellt när dom engelska orden böjs på svenskt vis.......
Brace = ribba / ribbor Bracing= ribbning / beribbning
Så vad du undrar över är alltså material till gitarrlocks- och bottenribbor.
|
|
|
Post by gurra11 on Jun 5, 2011 23:03:06 GMT 1
Tack för svaren. Om fabrikerna använder sågat virke till sina gitarrer så borde det duga åt en amatör också
|
|